LTC4224-1/LTC4224-2
5
422412fa
PIN FUNCTIONS
SENSE1, SENSE2 (Pins 1,10): Current Sense Input. Con-
nect this pin to an external sense resistor. The current limit
circuit controls GATEn to limit the voltage between V
CCn
and SENSEn to 25mV . An Electronic Circuit Breaker (ECB)
is active during current limiting and trips after 5ms. To
disable current limit, connect this pin to V
CCn
.
V
CC1
, V
CC2
(Pins 2, 9): Supply Voltage and Current Sense
Input. An undervoltage lockout circuit disables the part
until V
CC
, the higher of V
CC1
and V
CC2
, exceeds 2.4V . The
lower supply is disabled until it exceeds 0.8V .
GATE1, GATE2 (Pins 3, 8): Gate Drive for External N-channel
MOSFET . A charge pump sources 10糀 from GATE to turn
on the external MOSFET . An internal clamp limits the gate
voltage to 5.5V above the higher of V
CC1
and V
CC2
. During
turn-off, a 1.5mA pulldown current discharges GATE to
ground. During short-circuits, a 125mA pulldown current
is activated to discharge GATE to ground.
FAULT (Pin 4): Fault Status Output. Open-drain output
that is normally pulled high to V
CC1
or V
CC2
by an exter-
nal resistor. It is pulled low when the ECB trips due to an
overcurrent condition at either supply. This pin may be
left open if unused.
ON1, ON2 (Pins 5, 6): On Control Input. A falling edge
turns on the external N-channel MOSFET and a rising edge
turns it off. A low to high transition on this pin resets an
ECB fault for the corresponding channel. Internally pulled
up to V
CC
by a 10糀 current source.
GND (Pin 7): Device Ground.
Exposed Pad (DFN Package Only): Exposed Pad may be
left open or connected to device ground.
FUNCTIONAL DIAGRAM
CHARGE
PUMP
422412 FD
0.8V
0.8V
2.4V
V
CC
+
+
+
+
CHARGE
PUMP
+
GATE
PULLDOWN
LOGIC
CONTROL
GATE
PULLDOWN
0.8V
+
0.8V
V
CC1
V
CC2
10糀
10糀
GATE1
GATE2
ON1
FAULT
ON2
SENSE2
SENSE1
GND
ACL1
ACL2
10糀
10糀
5.5V
5.5V
ON2
ON1
ECB1
ECB2
V
CC1
UV
V
CC2
UV
25mV
25mV
V
CC
V
CC
V
CC
V
CC
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LTC4225IGN-1#PBF
IC CONTROLLER HOT SWAP 24-SSOP
LTC4230CGN#TRPBF
IC CONTRLLR HOT SWAP TRPL 20SSOP
LTC4232CDHC#TRPBF
IC CTLR HOT SWAP 5A 16-DFN
LTC4240IGN#TRPBF
IC CTRLR HOTSWAP CPCI I2C 28SSOP
LTC4241IGN#PBF
IC CTRLR HOTSWAP 3.3V AUX 20SSOP
LTC4242CUHF#TRPBF
IC CNTRLR HOT SWAP 38-QFN
LTC4244CGN-1#TRPBF
IC CTRLR HOTSWAP PCI 20-SSOP
LTC4245CG#TRPBF
IC CNTRLR HOT SWAP 36-SSOP
相关代理商/技术参数
LTC4224IDDB-2-PBF
制造商:LINER 制造商全称:Linear Technology 功能描述:Compact Dual Low Voltage Hot Swap Controller
LTC4224IDDB-2-TRPBF
制造商:LINER 制造商全称:Linear Technology 功能描述:Compact Dual Low Voltage Hot Swap Controller
LTC4224IMS-1#PBF
功能描述:IC CTLR HOT SWAP DUAL LV 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件
LTC4224IMS-1#TRPBF
功能描述:IC CNTRLR HOT SWAP DUAL 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件
LTC4224IMS-1-PBF
制造商:LINER 制造商全称:Linear Technology 功能描述:Compact Dual Low Voltage Hot Swap Controller
LTC4224IMS-1-TRPBF
制造商:LINER 制造商全称:Linear Technology 功能描述:Compact Dual Low Voltage Hot Swap Controller
LTC4224IMS-2#PBF
功能描述:IC CNTRLR HOT SWAP DUAL 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件
LTC4224IMS-2#TRPBF
功能描述:IC CNTRLR HOT SWAP DUAL 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件